Timex Analog Chronograph Podręcznik Użytkownika

W223 NA 222-0950012W223_Analog2_NA_Cvr.qxd 6/5/09 9:37 AM Page cvr1

TO USE CHRONOGRAPH FOR LAP OR SPLITTIME MEASUREMENT:1) PRESS pusher “A” to bring up CHRONOGRAPH display; “CH LAP” or “CH SPL” will appear.2) PRESS pus

NOTE:1) While in setting of any mode, if no pusher ispressed for 90 seconds the display will automati-cally return to TIME / CALENDAR mode.2) While in

TO SET THE TIME1) Pull crown all the way out and turn to correcttime.2) Push crown in to restart.Note: 24-hour display will set automatically.TO SET T

NOTE: Remember to set time for am or pm (sun ormoon).TO SET DATE:1) PULL out crown to “B” position.2) TURN crown clockwise to correct date.3) PUSH in

• The seconds sweep hand shows “secondselapsed” for chronographTIME, CALENDAR, CHRONOGRAPH This chronograph watch has three functions:TIMETO SET THE T

NOTE: PRESSING and HOLDING either pusher “A” or“B” will cause the hands to move continually until thepusher is released.STANDARD CHRONOGRAPH MEASUREME

SETTING THE DATE1) PULL the crown out to the 1st position “B”.2) Turn the crown counter-clockwise to set the date.*If the date is set between the hour

*Do not push crown to normal position while thechronograph second hand returns to zero position.It stops on the way when crown is returned to normal p

TIMETO SET THE TIME:1. PULL crown out to “C” position.2. TURN crown either way to correct time.3. PUSH crown in to “A” position.TO ADJUST TO A NEW TIM

TO ADJUST CHRONOGRAPH HANDS:1. PULL crown out to “B” position.2. PRESS pusher “B” until the hand at the 10 o’clockeye resets to the “30” position.3. P

TIMEX®WATCHESCongratulations on purchasing your TIMEX®watch. Please read these instructions carefully tounderstand how to operate your Timex timepiece

NIGHT-MODE®FEATURETO USE NIGHT-MODE®FEATURE:1. PUSH and HOLD Crown to “D” position for 4 sec-onds to activate NIGHT-MODE®feature.PRESSING any pusher w

TIMETO SET THE TIME:NOTE: The stopwatch must be stopped and reset tothe zero position prior to setting the time.1. Pull the crown out to position 2.2.

ELAPSED TIME RINGIf your watch is equipped with a rotatable outer ringon the face, with numbers corresponding to minutes,you can use this Elapsed Time

If within the first minute, a distance greater than onemile or kilometer is covered, multiply the tachymeternumber by the distance to get the actual r

FOLDOVER CLASPBRACELET1. Find spring bar that con-nects bracelet to clasp.2. Using a pointed tool, pushin spring bar and gentlytwist bracelet to disen

BATTERYTimex strongly recommends that a retailer or jewelerreplace battery. If applicable, push reset button whenreplacing battery. Battery type is in

do not allow limitations on implied warranties and do notallow exclusions or limitations on damages, so these limi-tations may not apply to you. This

49Mexico and Central America 01 800 01 06000 (U.S.);Portugal +351 212 555 460; UK, Middle East and Africa +4420 8687 9620For other areas, please conta

TABLE OF CONTENTS2 How to Start Your Watch3 Water and Shock Resistance4 Indiglo®Night-Light5 Analog/Digital Models18 Multi-Function Models20 Day/Date/

WATER AND SHOCK RESISTANCEIf your watch is water-resistant, meter marking(WR_M) is indicated.*pounds per square inch absoluteWARNING: TO MAINTAIN WATE

ANALOG/DIGITAL MODELS4-PUSHER ANALOG/DIGITAL MODEL WITHINDIGLO®NIGHT-LIGHT & NIGHT-MODE®FEATURE5ENGLISH2. Watch is not a diver watch and should no

DIGITAL DISPLAY1) The Digital display changes to each function everytime you PRESS pusher “A”. (As illustrated below):TIME / CALENDARDAILY ALARMCOUNTD

• To view or change the display to TIME, repeat thesteps above.NOTE: “A” or “P” will appear when the 12-Hourformat is selected.• Set this time to coor

NOTE:• When the alarm sounds, it will beep for 20 seconds.• To stop the alarm beep, PRESS any pusher.• PRESS and HOLD pusher “C” for 2 seconds insetti

TO USE COUNTDOWN TIMER1) PRESS pusher “A” to bring up COUNTDOWN TIMERdisplay. “24 HR TR” will appear.2) PRESS pusher “D” to let hour flash.3) PRESS pu